HALO - 6” Recessed New Construction Housing for use with LED Integrated Trims or Modules- E750ICAT  
 
Product Description 

Recessed 6” aperture new construction housing for use with LED integrated trims or modules. Suitable for 2x8 residential framing or commercial plenum construction, type IC rated and can be used in direct contact with insulation*. Airtight rating reduces airflow between living spaces and unconditioned areas providing additional energy savings. Use with Halo® LT56, SMD6, RL56, RA56, SLD6 LED integrated trims and the ML56 LED modular recessed lighting system.  
 

• For use in insulated ceilings
• Air-Tite exclusive housing gasket
• Air-Tite tested per ASTM-E283
• All-Nail bar hangers with preinstalled nail and integral T-grid clip
• q-channel interlocking hanger bars
• Hanger bars feature Pass-N-Thru tool-less shortening
• Quick connect push-in wire nuts included
• Hinged junction box with Slide-N-Side
• Socket bracket adjusts lamp to various trim styles and designs

Specification Features
 
Housings
• Single wall precision rolled aluminum housing with interlocking construction maintains concentricity
• Adjusts vertically to accommodate 3/8” to 1” thick ceilings and locks in position with (3) setscrews
• V notches facilitate use of guide strings or laser lines for precise positioning
• Shipped with paint overspray protector installed
• Housing can be removed from below the ceiling for service or splice inspection
 
Plaster Frame
• Compact galvanized steel plaster frame with integral bar hanger receivers
• (2) regressed screws provide positive horizontal bar hanger locking from below the ceiling
• Integral gasket achieves ASTM-E283 airtight code compliance without additional gaskets or caulk 
 
Junction Box
• Compact galvanized steel junction box with 16in³ internal volume
• Listed for (10) #12 or (14) #14 AWG 90˚ C splice conductors
• (4) ½” conduit pryouts positioned to allow straight conduit runs
• (3) Slide-N-Side™ nonmetallic (NM) wire traps allows wiring outside the box
• Accepts 14-2, 14-3, 12-2, 12-3 U.S. and 14-2, 14-3, 12-2 Canadian NM cable
• (3) 4-port push wire nuts with clear caps for quick and reliable mains voltage connections
• Hinged door with offset cover for easy wire access
• Junction box is repositionable 90° on plaster frame to avoid obstructions 
 
Bar Hangers
• Captive preinstalled All-Nail™ bar hangers support housing at any point along span
• Pass-N-Thru™ feature adjust bars from 7-1/4” to 24” wide without removal
• Score lines allow “tool-less” shortening for 12˝ joists
• Captive nail penetrates standard and engineered lumber
• Leveling flange aligns plaster frame with framing
• Integral clip attaches directly to tee-bar 
 
Connector
• Two-conductor wire mount connector is rated for 120-277V CAUTION – verify LED module input voltage is compatible with the input voltage of the housing. If uncertain, consult a qualified electrician
• cULus listed with Halo® LT56, SMD6, RL56, RA56, SLD6 and ML56 family of LED integrated trims 
 
Code Compliance
• Type IC inherently protected, suitable for direct contact to air permeable insulation and cULus listed for damp locations
• Not for use in direct contact with spray foam insulation, consult NEMA LSD57-2013
• Wet location listed in covered ceilings and IP56 certified with select trims
• Airtight per ASTM-E283
• Can be used for State of California Title 24 high efficacy luminaire compliance
• Suitable for use in clothes closets when installed in accordance with the NEC 410.16 spacing requirements
• Contains no mercury or lead and RoHS compliant